Program GM 2020+ CAN FD Smart Key with Xtool Bypass PIN

 People programmed many of these GM 2020+ CAN FD models by xtool. Autel cannot retrieve pin on the machine, OBDSTAR sometimes service is down, xtool is stable on this and very fast.

x100 tablets with new updates and CanFd 100% no security code like old models.

 

Requirement:
Scanner has to be connected to the internet.

You must have xtool can fd adapter (Don’t use CAN FD adapter from other brands)

Xtool tablets that compatible with xtool adapter

Compatible with the following: 

• Xtool X100 PAD2/PAD3/Elite series
• PS80 PS90 series
• D7, D8, D9 series
• EZ400 Pro 
• A30 Pro
• A80/A80 Pro/A80 Pro Master
• AutoProPAD Full
• AutoProPAD G2
• AutoProPAD G2 Turbo

 

Follow CAN FD Models are supported, keep updating

2021+ Buick Envision
2020+ Cadillac CT4/CT5
2022 Cadillac XT4/XT5/XT6
2020+ Cadillac Escalade
2020+ Chevy Corvette
2021+ Chevy Tahoe
2022+ Chevy Silverado
2022 Chevy Suburban
2022 GMC Sierra
2021-2022 GMC Yukon

 

 

Programming example:

Chevrolet Silverado 2023 all keys lost using Can FD adapter & xtool tablet

The procedure should be similar to other GM CAN FD models.

Select Brand->Region->Model->Year-> Free PIN method

The CANFD adapter and OBD much be connected, otherwise, it will not communicate.
Select All Keys Lost

Make sure all keys are away from the sensing area (water cup holder).
If akl cannot switch on ignition, open/close the driver door every 10 seconds and observe the instrument unit the instrument response for procesing the next step
Close all doors
communicating

Put the key to be programmed into the induction zone cup holder, keep other keys sways from the induction zone

Press the start button for 2 seconds, observe the meter, if the display does not change, release and hold the start button again until there is a change press OK to continue

Program 1st key success

Follow xtool tablet prompts to program 2nd key until finished.

 Done. 

Xtool X100 PAD2 Program Audi A3 2016 MQB Key

 Tutorial: how to program Audi A3 2016 new MQB key using xtool x100 pad2, pad3 or x100 elite. Key can be generated by Keydiy ZB series remotes only. 

 

Step 1: Generate remote with keydiy 

the original key is 48 MQB
use keydiy kd-x2 and ZB-series remote to generate new key

Select option Audi- A3- Audi MQB FOLD (No KeylessGo)

generate remote successfully

the remote need to be programmed

 

Step 2: Program key with xtool

connect xtool x100 pad2 with vehicle via OBD port
turn on ignition switch with the original key
in x100 pad2, go to Select by model-Audi- A3/S3/RS3-> 2013/6- MQB platform

Follow 3 steps to program key
1. Read Immo data
2. Make dealer key
3. Learn key

Read immo data

then make the dealer key
input working key into kc100
make dealer key success
place a new key into kc100
Make dealer key success

Now start to learn key
insert the working key into ignition switch
switch ignition on
insert number of keys to be learned: 2

change another key if 1st key is learned successfully

learn key finished
test both keys

Done.

http://www.key-programmer.org/2022/07/26/program-audi-a3-2016-mqb-key-with-xtool-x100-pad2/

Xtool Program 2018+ Chrysler FCA Proximity

 Xtool tech now released 2018+ Chrysler Dodge Jeep proximity smart key programming functions as well. Here is the programming instruction.

 

Tools you need:
Xtool key programming tablets (X100 PAD3/X100 PAD Elite)
Chrysler 12+8 SGW Bypass cable
WiFi connection

How to Connect 12+8 Adapter:

Find the SGW module, take the 12-PIN connector and the 8-PIN connector off, then connect these connectors to the Bypass cable.
Here is an example on a 2018+ Jeep Grand Commander.

For other models, check the SGM Location.

When connecting to STAR connector
The STAR connector used for Security Gateway is always colored green, and has several connectors attached to them.

To connect the cable to a STAR connector, plug the pins into the connectors. The connecting pin locations may vary between different models, take the 2021 Dodge Challenger as an example

in this situation, we connect the read pin into the green wire and the black pin into the yellow wire.

 

Program process:
Take a 2020 Jeep Wrangler with a smart key as an example.
1. Open the diagnosis app and go through this menu:
Jeep- Proximity/Fobik (RFH)- Wrangler 18-
Xtool X100 PAD 3 will ask to make sure the main cable and SGW bypass cable are connected.

2. Before programming, we suggest reading the key number that is registered on the car. Press the Number of Keys menu to check the key number

3. When key programming, the vehicle needs s security code to verify the process. Read the security code first.
Make sure you are connected to the internet. Then click Read security code menu.

4. Read security code success

5. Press Add smart key to start key programming.
Follow the instructions on the device, turn emergency indicators and switch the ignition off,
*This menu is also applied to all keys lost situation.

6. Xtool will ask you for a security code. The device will automatically fill in the code.

7. Follow the instructions, put the key close to start button, then press and hold this button within 20 seconds until the device pops out the result, Press OK when you are ready for this process.

8. Programming success.

Related reading: Xtool Program Ford 2015+ Proximity AKL with active alarm

Program 2015 Up Ford All Keys Lost with Xtool Tablets

 Xtool tech released 2015 onwards new Ford proximity all keys lost with active alarm function as well.

 

Tools you need:
Xtool key programming tablets (X100 PAD3/X100 PAD Elite)
Ford AKL alarm bypass cable
WiFi connection

 

How to Connect:
1.Connect the main cable to the female obd2 socket of the Ford cable, and connect the tablet or VCI box to the other side of the main cable.2. Connect the male OBD2 socket of the Ford cable to the OBD port of the vehicle
3. Take the battery clip off from the car’s battery and connect the 2 battery clips to the battery
4 There is also a battery clip (read cable with ‘Battery Clip+’ tag on it) on the cable. Connect it to the positive battery clip on the car.

How it work?
Ford AKL Alarm Bypass Cable can:
Allows you to perform Ford smart key all keys lost via Xtool devices with a VCI Box
(H6 Pro, A80 Pro, X100 MAX etc)
Optimize the process on Ford smart key all keys lost via Xtool devices without a VCI box
(X100 PAD2, X100 PAD3, H6 Elite, D7/D8 etc)

Controls vehicle battery on/off with a switch on your hand and save your time from the repeating battery reconnecting process.

Programming Process:

Take a 2018 Ford Edge with an active alarm as an example and read its EEPROM data without any keys available
1. Make sure the cable is connected properly, the select
Ford V27.30 or higher- North American Ford- Smart key system- Edge- 2016-2020

2. Select All keys lost. Choose the menu depending by the status of the vehicle. Considering the alarm is on now, here we select ‘Alarm activation’

3. Open the door on the driver’s side. Use a screwdriver to jam the door latch on the locked position but keep it opening.
The door should keep open but locked until the entire process is done. When it is done, click OK to continue,

4. Select Reading EEPROM first

5. If the cable is connected, switch off the battery

6. The device will try read the EEPROM by communicating with the ECYU.
Switch on the battery and check if the alarm still goes on.

7. If the alarm still goes on, switch off the battery and wait for 10 seconds, then try switch off and on again

8. If the alarm is off, disconnect the cable to the battery, connect it back to battery clip of the car, tighten it, and close the hood, click OK to continue.

9. Reading EEPROM data. The process will take 10 minutes

10. WHen EEPROM reading is done. it will generate a bin file, Save file on Internal Storage folder.

*If you are using a device without VCI but not using the cable, you must remove/install the battery clip every time the device noted you to disconnect/reconnect to the battery.

http://www.key-programmer.org/2022/03/03/xtool-program-2015-ford-all-keys-lost-with-active-alarm/

Program 2018+ Nissan Sylphy/Sentra AKL with Xtool X100 PAD2/PAD3

 Here's the instruction on 2018+ Nissan Sylphy/Sentra all keys lost smart key programming with Xtool key programming tablets.

 

 

Tools you need:

Xtool X100 pad2/x100 pad3

Main Cable & OBD2-16 Connector

Nissan 16+32 CGW gateway adapter

Stable Wi-Fi connection

PC or smartphone

 

 

HOW TO CONNECT

No matter you're working on add key or AKL, key programming for 2018+ Nissan Sylphy/Sentra requires an extra CGW (Controller Gateway) adapter.

The CGW module for Nissan Sylphy/Sentra is located inside the driver-side footwell, above the pedals. To connect the vehicle to the device, pull out the wiring harness from the module, and connect it to the adapter.

 

The other side of the adapter connects to the main cable. Connect the main cable to the device and the adapter to start the full process.

 

 

 

PROGRAMMING PROCEDURE:

1. Open the diagnosis app, and go through these menus:

Diagnosis – Immobilization – NISSAN (V27.10 or later version) – Program keys – Select from vehicle – China(Only partially) – New Sylphy (B18) – Key matching (All key lost)

2. The software will pop up 2 notices. Please read carefully and make sure you have done all the processes before you get started.

3. After you clicked OK, this menu will show up. Now put a new key near the ignition switch, then press “Read key” to continue.

In all-key-lost situations, the original keys will be deleted in this process. If you only want to add keys, we suggest to use “Bypass” menu.

4. You can use this method to read 2 keys each time. If you want to program more keys please select “Add key” menu afterwards. Now we read 2 keys, then click “Next”.

5. Now the screen will pop up a notice. Please take a photo about the information it shows up, and go to the website shown on the screen.

Please leave this screen until you uploaded the calculate results to the server. Do not kill the APP. Do not turn off the screen. Do not disconnect the device to the car & network. Or the code will be invalid, and you will have to repeat the entire process.

6. Open the website using your smartphone or PC. It will show as follows (In Chinese; will add English version soon):

7. After input the serial number and the dynamic code shown on the tablet, you will see this:

8. Press the blue link to download the data. The data file you received will be started with “SupportData1”. Please note that now we can only calculate the data via 3rd party organizations so please send it to them.

9. When you received the calculated data from 3rd parties, the file will be started with “SupportData2”. Press the blue button to upload the data and the next page will show the results. The results will also be uploaded to the device, so you don’t need to type the results.

10. Now back to the tablet and press “OK”. The menu will show the keys as “Programmed”.

11. Put one of the programmed keys near the ignition switch. Click “Match key” and check the results.

 

If don't use the bypass adapter, you can also calculate PIN and program key with xtool, check guide here http://blog.obdii365.com/2021/10/20/2018-2020-nissan-kicks-calculate-pin-and-program-smart-proximity/

Xtool X100 Pad2 Add Nissan Qashqai 2019 Key without PIN

 Nissan Qashqai 2019 is programmed successfully without reading pincode or releasing steering lock with xtool x100 pad2.

it’s my first time programming Qashqai 2019 so I want to share the tip.

Didn’t read pin code, directly program key open driver door and close it then push the start button, wait 5 seconds and job done.

The key is original not generated.

The car is imported from Europe.

Here is the xtool x100 pad2 NISSAN Qashqai Function List V27.14 claimed by the manufacture.

 

1. Nissan Qashqai from China:

With smart key system (20 pincode): program smart keys.

Without smart key system (20pincode): program key

 

2. Nissan Qashqai from Europe:

 

2007 -2009: program remote  – Fault code, erase DTC, program keys.

 

2009-2013: program remote – Erase DTC, program keys, release steering lock

 

2009-2013: Mechanical key – Erase DTC, program keys, release steering lock

 

2009-2013: Smart key system – program smart keys, erase all smart keys, program steering lock

 

2014 – : Immobilizer system  – Type1 – program smart keys

 

2014 -: Immobilizer system  – Type2 – program key

Good to know:

Obdstar X300 Pro4 / obdstar X300 DP Plus is also able to program Nissan Qashqai 2019 Prox all keys lost via obd.

Read procedure here: http://blog.obdii365.com/2021/12/09/obdstar-program-nissan-qashqai-2019-prox-all-keys-lost/