Xtool X100 PAD2 Program VW Audi 4th 5th Immo via Online Mode

Xtool X100 PAD2 updated VW/Audi 4th 5th online programming in Feb. 2020.  Online mode is not a necessity, but offers another solution.

4th and 5th Immo online key programming for Audi

Step by step procedure:
1. Turn on xtool x100 pad2. Select Diagnosis in the side menu and then select Audi under Immobilization menu Audi key programming interface will be shown below, select 4th/5th Immobilizer system

2. Select 5th Immobilizer system. Turn on ignition and press OK

3. Select Online Mode

4.After selecting Online mode, wait for a while order payment information interface will be displayed.

5. Press Confirm payment button the order information interface and click OK in the prompt box.
Wait for payment completion and calculation result.

6. After calculation is complete, press OK.

7. Press Yes to make a dealer key

8. Connect the x100 pad 2 to the KC100 adapter and wait for the KC100 to be activated.After the activation is successfully, you will be prompted whether to bind the current device.

9. Press Yes. it will check the version information, and then wait a moment to load the firmware information.
10. After the firmware information is successfully loaded, the following interface is displayed.

11. Select Create A4/A5/Q5 key option, and put a key that ready to add to coil

12. Place the prepared key in the coil of the KC100 shown picture below

13.Click OK when wait for key creation and key data writing.

14. Make dealer key success.

15. Press Yes to Add a key.

16 Input the number of keys to match

17. Enter number of keys: 2 and click OK.
Turn on ignition switch.
All keys lost: Insert one dealer key into ignition switch ot make it close to the induction coil
Lost all: Insert a dealer key into the ignition or place it close to the induction coil
Follow the prompts and insert a dealer key into the ignition.

18. Click OK, the following message will be displayed: Aim the keys at the back of the key identification mark area, close to open the ignition switch to identify the key 2-1.
Switch to identify the key. Currently  2-1.
After success, the following message is displayed: Exit the key learning.

19. Key learning completed.

Done.

Check also:
Xtool X100 PAD2 + KC100 Program VW Audi 4th 5th IMMO key (offline mode)

http://www.key-programmer.org/2020/03/31/xtool-x100-pad2-adds-vw-audi-4th-5th-immo-online-mode/

Xtool X100 Pad2 Program Freelander 2 2007 Key

Another Land Rover Freelander 2 2007
Done with xtool x100 pad 2

First key I purchased would hold in slot.
Tried another key struggled but it held key in slot eventually.
Job done.
Aftermarket key.

Xtool X100 Pad2 Program 2015 Hyundai i40 Estate Remote

2015 Hyundai i40 estate remote programming by obd
Using xhorse remote and xtool x100 pad2.
Chip is 4d 70

Select from Vehilce-> General->i40 (VF)-2010 to 2018->Remote System->Program remotes


Does it want pin code?
Yes it does if programming chip.
No pin required for remote programming
So way to clone with vvdi key tool or keydiy.

www.obdii365.com

Xtool X100 Pad2 Program Polo 6N 2001 All Keys Lost

VW Polo 6N 2001 all keys lost , pick decode Trunk by lishi, read immo get pin and program with Xtool x100 pad2. ID44 (7945 precode ID44) no way get right pin by obd with several tools.

2000- 2001 is ID44, before ID42. Pin get by reading immobox 24C04. No correct pin read by OBD. 

Xtool X100 Pad2 Program KIA Soul 2011 All Keys Lost

KIA Soul 2011 all keys lost, read pin (ID46 Philips crypto) code and program 2 key with xtool x100 pad2 (pin also success with X300 pro4, Ikey820)

Xtool X100 Pad2 Adds 2014 Ford Kuga Prox Key

Programmed 2014 Ford kuga proximity key today using xhorse remote and xtool x100 pad2. Under China ford worked perfect about 2 mins including security access.

Done quite a few prox on Fords..xpad2 loves them.

Xtool X100 Pad2 Adds 2016 Ford Ranger Key

2016 Ford Ranger Hitag Pro chip.....added spare basic key with xtool x100 pad2 in 20 seconds

Xtool X100 Pad2 Adds 2013 SantaFe Smart Key

2013 Hyundai SantaFe proximity added using Xhorse prox key and xtool x100 pad2.
no testers would pull pin...once I sourced the pin it worked great.

Xtool X100 Pad2 Adds Key to VW Polo 2015 MQB

VW polo 2015 MQB add key. Read immo data (was fast) and make dealer key - learn both keys in successfully with Xtool X100 Pad2.

I remember the customers key being a Q and my key (aftermarket) that worked is a BA.

Here's simple procedure:
VW - MQB Platform - READ IMMO DATA - (all immo data screen will pop up) - MAKE DEALER KEY (connect kc100 and read data from existing key, then insert blank key) - LEARN KEY (enter value 2) then turn ignition with key 1 (dash shows ‘1-2’) remove and turn ignition with key 2 (dash shows ‘2-2’) then remove key.
Process done. Press both remotes 3 or 4 times until it kicks in.

www.obdii365.com

Program 2010 Fiat Punto All Keys Lost with Xtool X100 PAD2

How-to: program 2010 fiat Punto Evo All keys lost.

2010 fiat Punto Evo Delphi ID46 All keys lost
Decode lock with Lishi sip22.
Aftermarket key
Read 5-digit code no problem
Pre coded remote key.
Programmed new key including remote (normal one).
Success with xtool x100 pad2.
All work perfectly.

How to Pre code the key?
select Fiat->Europe->Punto->2006 to 2011->Pre-code key->Remote Key->All keys lost
And it's there on screen
pre code and asks in just chip or a remote key select remote key pre code done
The back and click all keys lost
And follow screen
Fast and easy.
Obviously must have kc100 to pre-code.

Credit to Mr. Brett.
www.obdii365.com

http://www.key-programmer.org/2020/03/13/how-to-program-2010-fiat-punto-evo-id46-all-keys-lost/